Whats here 4 YOU ?

Mouseover for Details

Very Good Articles

WiTricity

FUNNY PICS

INTERESTING Facts - really worth a Glance

Movies updated

Do It Yourself (DIY)

click on READ MORE for full article

Sunday, September 12, 2010

WiTricity-wireless power transefer or wireless energy transmission..

More Coming Soon.....

FOLLOW me if interested.

Witricity - Do It Yourself 
You can transfer electricity wirelessly by following the simple instructions below, in a very affordable, easy-to-build and easy-to-understand way.
This will work only in short range (9CM) because I built it for the purpose of demonstrating the working principle only(which will be understandable to almost every one). By using higher frequencies, thicker coils and other advanced modifications one can reach a range of about 2 Meters.

 

For further help and doubts you can contact me by mail or by live CHAT (on WiBar below).
Please do join our community via FaceBook (on the WiBar below) and follow on Twitter @skMobeen.
Please do COMMENT and give your valuable suggestions.

All rights reserved. Above content not to be shared or published without permission from the author.




18 comments:

Anonymous said...

Great Job done.

MobeeN said...

THANK YOU VERY MUCH MANISH

Unknown said...

MobeeN m HARDIK from gujarat.i want you to conduct a seminar in our techfest. DO RPLY me as soon as possible.

Waiting for positive response.

Unknown said...

hiiii mobeen i too want to make project on wireless power transmission...suggest any idea.....

pb said...

hey mobeen i have tried this but didnt get any result..i did 26swg wire with 50 turns n 6cn diameter primary n secondary coils and tried to light up a 5 v led distance was less than 9 cm but no result. plss help me out.. mail me at rockietoddy@yahoo.in

thanks.

pb said...

hey mobeen i have tried this but didnt get any result..i did 26swg wire with 50 turns n 6cn diameter primary n secondary coils and tried to light up a 5 v led distance was less than 9 cm but no result. plss help me out.. mail me at rockietoddy@yahoo.in

thanks.

pb said...

I took 25swg 50 turns 6mm diameter primary and secondary coil connected to 0.05µF capacitance.According to the calculation i made,power transfer to secondary coil happens inbetween 118-190khz frequency of function generator buts it not happening...

can your people help me out ?

pb said...

I took 25swg 50 turns 6mm diameter primary and secondary coil connected to 0.05µF capacitance.According to the calculation i made,power transfer to secondary coil happens inbetween 118-190khz frequency of function generator buts it not happening...

can your people help me out ?

MobeeN said...

hey bharath, hi. I'm lille busy today i'll reply by tonight. Plz excuse for delay. I have to leave for GD-PI.

daisy said...

how did you connect the capacitor to the LED and capacitor to the signal generator

MobeeN said...

i'll post detailed pics 2moro here it self.

ravinder singh said...

hi mobeen..
can you tell me the voltage and current rating of function generator..

MobeeN said...

Sorry folks, i was busy and was unable to post pics which i promised earlier. I'll hope fully do it this weekend.

MobeeN said...

@ravinder - Voltage and current rating of function Gen is same as required by the LED i used. Simple CS yaar !! Any how all the best !! Feel free to mail for further help.

Unknown said...

hi.......
i want to know about your project on witricity that
for resonance the receiving and transmitting circuits should have same resonant frequency
but you used two different coils for receiver and transmitter, then how they gonna have same resonant frequency if their inductances are
going to be different?
please reply the answer on this post here itself...

Unknown said...

hi.......
i want to know about your project on witricity that
for resonance the receiving and transmitting circuits should have same resonant frequency
but you used two different coils for receiver and transmitter, then how they gonna have same resonant frequency if their inductances are
going to be different?
please reply on this post here itself...

Unknown said...

hello sir first of all i give u congrts to provide a good source for the knowledge. But i think that if u give some explanation on this topic then it is fine. currently i m working on this topic also and face a lot of problem ao get moer desired result .. so i want to get some help from ur side...

Anonymous said...

hi,
wt is the diameter of the two coils plz send answer to varunrajurirocks@yahoo.com

Post a Comment